
词语导航
基本信息
词语:给定尺寸
繁体:給定尺寸
拼音:gěi dìng chǐ cùn
英语翻译
【化】 given size; intended size
分词翻译
给的英语翻译:
allow; give; grant; let; tip
【医】 administer
定的英语翻译:
book; order; decide; fix; stable; surely; calm
尺寸的英语翻译:
dimension; measure; measurement; size
【化】 dimension
【医】 dimension
翻译例句
1. 公差是零件允许的变动量或给定尺寸允许的总变动。
Tolerance is the amount of variation permitted in the part or the total variation allowed in a given dimension.
2. 在印刷技术中,给定尺寸的铅字所占有的表面积。这样,一个8点的铅字则占有8点em的印刷面积。
In printing, the surface area taken up by type of a given size. Thus an8point type occupies a print area of8point EM.
3. 所用的加热炉的尺寸与型号要进行控制,使每项操作的温度能够在给定的范围内。
The furnace must be of the proper size and type and controlled, so the temperatures are kept within the prescribed limits for each operation.
4. 通过给定的热处理所得到的硬度取决于淬火速率、含碳量和工件尺寸。
The hardness obtained from a given treatment depends on the quenching rate, the carbon content, and the work size.
5. 一个图纸层面上的给定部品的尺寸(比如,细部图)并不能强制地标注在另外一个层面的图纸上(比如说,装配图)。
A dimension specified for a given feature on one level of drawing, (for example, a detail drawing) is not mandatory for that feature at any other level (for example, an assembly drawing).
6. 每行都按给定的树木尺寸和所在位置打印出可见的树木数量。
Each line will consist of the number of trees of the given size, visible from the given position.
7. 在给定裂纹尺寸与载荷条件下,利用断裂评定程序对一裂纹缺陷进行了评定,得到了海底管线失效评定曲线(FAD图)。
Under given crack dimensions and load condition, to appraise to cracks defects with fracture appraisal program and obtained submarine pipeline failure appraisal diagram (FAD).
8. 以6 -SPS并联机床为例,对给定工作空间的并联六杆机床结构尺寸设计进行了分析与研究。
In this paper, taking 6-sps parallel machine tool as an example, design for the construction dimension of 6-sps parallel machine with given workspace is studied.
9. 通过给定的热处理所得到的硬度取决于淬火速率、含碳量和工件尺寸。Www.WEnTIYI.Com
Thee hardness obtained from a given treatment depends on the quenching rate, the carbon content, and the work size.
10. 计算结果表明:在给定河谷形态、尺寸和材料性质条件下,沉积层表面各点的响应显著放大。
Results show that response at surface points of the alluvial soil deposit are amplified significantly for given conditions of shape, dimension and material properties of the soil and the canyon.
11. 给定紧凑颗粒的图像序列,不经过精细分割,而是基于边缘密度来计算平均尺寸(平均直径)。
Given image sequences of closely packed particles, the topic is that of estimating average size (average diam-eter) of packed particles, applying edge density without explicit segmentation.
12. 因为对于一个给定的抛光砂轮,它每一次能抛光的总表面积有限,所以最大限度地扩大砂轮的尺寸能够使每次抛光的部件的总表面积达到最大。
Since there are limits on the maximum amount of part surface area that can be processed with a given wheel size, maximizing the size of the wheels will allow the maximum number of parts per run.
13. 在给定晶体管中的第一栅极导体和第二栅极导体的相对尺寸控制晶体管的阈值电压。
The relative sizes of the first and second gate conductors in a given transistor control the threshold voltage for the transistor.
14. 这可以从不同的焊接到焊盘尺寸为最大功率耗散,和灰给定的最小焊盘尺寸。
This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation.
15. 按高斯光束分布计算出给定腔长的反射镜曲率半径、光腰及镜面处光斑尺寸等参量。
For a given cavity length, the parameters, including the curvature of reflector, waist radius and spot size on reflectors, are calculated according to the Gaussian profile.
16. 因此,在全伸长下最大载荷的所给定的尺寸是合理的导向件尺寸并可保证免于维护。
As a result dimensioning to the Max. Load in the fully extended position gives reasonable guide dimensions and trouble-free service.
17. 对任何给定的基本尺寸,公差范围和偏差可以相对于被称为零线的零偏差线来确定。
For any given basic size, a range of tolerances and deviations may be specified with respect to the line of zero deviation, called the zero line.
18. 对模拟机构给定输入件的驱动尺寸,确定动平台的位置和姿态,分析其运动参数的变化。
When the driving dimensions of driving limbs are modified, the configurations of the simulation mechanisms are varied correspondingly, and the kinematic parameters of the moving platform are solved.
19. 对给定的门绝缘体,设备原理上需要维持绝缘体厚度与横向尺寸成比例(参考文献1)。
For a given gate dielectric, device physics require maintaining the dielectric thickness in proportion to lateral dimensions (Reference 1).
20. 注:为了方便客户安装要求,本表给定的数值系与蝶阀链接的标准法兰尺寸,简图中尺寸代号仅是其中一部分。
Note:In order to be convenient for the installation of clients, the numerical value, butterfly valvejoint standard flange size and size code in the table are only one part of them.
21. 结论表示,优化后白勺机构具有确定白勺几何尺寸,可以满足运动学要求,并能实现给定白勺运动规律。
The results show that the optimized geometry agency has determined, to meet the kinematic requirements and to achieve a given law of motion.
22. 提出了从动链轮在其步进角的中间范围内,作恒速比传动的几何条件以及实现给定步进角的机构尺寸的设计方法。
The design example has shown that both the design method and monufacture of the step motion mechanism are simple and…
23. 提出了从动链轮在其步进角的中间范围内,作恒速比传动的几何条件以及实现给定步进角的机构尺寸的设计方法。
The design example has shown that both the design method and monufacture of the step motion mechanism are simple and…
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
