涂过用英语怎么说，涂过的英文翻译

词语导航

基本信息

词语：涂过

繁体：塗過

拼音：tú guò

英语翻译

【建】 coated

分词翻译

涂的英语翻译：

besmear; blot out; imbrue; scrawl; smear; spread
【医】 apply

过的英语翻译：

across; cross; excessive; over; pass; spend; through
【医】 per-

翻译例句

1. 埃尔南德斯承认他从未涂过睫毛膏。

Hernandez admitted that he never wore eyeblack.

2. 倒入涂过黄油的盘中，烤半个小时。

Put butter into pan and bake for half an hour.

3. 涂过色的手掌按到牛皮纸上，作为树枝。

Press your painted palm onto the craft paper. This will be the tree"s branches.

4. 这个星期这个糊涂过去的缺点暴露了出来。

This week the shortcomings of this muddling-through were laid bare.

5. 我稀里糊涂过了一年。

One year had passed by before I realized it.

6. 墙被涂过了。

The wall was coated.

7. 射线衍射分析结果表明冷喷涂过程中，无氧化现象发生。

Result for X-ray diffractometer test indicates that no oxidization occurred during the spraying process.

8. 探讨喷涂过程中羟基磷灰石晶体的相变化与结构稳定性。

Phase changes and structural stability of hydroxyapatite in this process were explored.

9. 电爆喷涂过程中金属丝阻抗及相关参数变化规律的研究。

The variation of the wire impedance and correlated parameters during WESC process is in-depth researched.

10. ⊙、我想我还是不会装糊涂过于坚持才把这份爱变的唐突。

I don"t think that I was too insist on playing dumb to get this love change abruptly.

11. 这里有成千上万本书籍，无疑是禁书、被乱涂过的书或偷来的书；

There were thousands and thousands of books, no doubt banned or graffitied or stolen.

12. 采用甩涂过程的基本方程，导得触变性流体在旋转圆盘上流动的速度分布。

With the basic equations of rotating coating process, the velocity distribution of the flow of a thixotropic fluid on a rotating disk was derived.

13. 通过建立专家数据库给出喷涂过程参数，实现了喷涂过程的参数初始化和控制。

Through founding an expert database, the spraying process parameters are worked out and the initialization and control of spraying process parameter are realized.

14. 与传统式空气喷涂方法相比，级减少喷涂过量及反弹现象，从而减少涂料损失。

Compared with traditional coating, this coating method will not result in phenomena like over-coating or coating rebound, so paint loss is cut down.

15. 过渡辊—在辊涂过程中，此辊转换涂料或其它液体涂布物从浸料辊到涂布辊上。

Transfer roll in roll coating, the roll that moves paint, conversion coating, or other liquid coating from the pick-up roll to the applicator roll.

16. 涂布辊—在辊涂过程中，涂装涂料，转换涂料，和其它液体涂料到运动的钢带的辊子。Www.weNtIyI.cOm

Transfer roll in roll coating, the roll that moves paint, conversion coating, or other liquid coating from the pick-up roll to the applicator roll.

17. 约克郡布丁的制作方法是将面糊浇注在涂过油的烘培罐里，然后在高温下烘烤加热至其膨胀。

Yorkshire pudding is cooked by pouring batter into a greased baking tin, and baking at a very high heat until it has risen.

18. 介绍了A38-51快于氨基锤纹漆的喷涂工艺及喷涂过程中可能出现的问题和解决方法。

A process of A38-51 fast-solidifying amino hammer finish as well as the operation hintswas described .

19. 本文主要介绍了一般垂纹粉末涂料，重点讨论了喷涂过程中可能出现悳问题和解决悳方案。

This paper described hammer powder coatings, and a spraying process of hammer powder coatings as well as the operation hints.

20. 结果表明：喷涂过程中粉芯丝材的表皮材料和芯粉材料能相互熔解和融合形成较均匀的固溶体；

The results show that the skin and the cored powders melted and fused to form homogeneous solid solutions during the arc-spraying procedure using the cored wires.

21. 在喷涂不可行的位置或者在固定的位置上，应采用刷涂。对于喷涂过的涂层的修补，允许使用刷涂。

Brush coating shall be used at locations where spray application is not feasible or at tie-in locations. Brush application is approved for repairs to spray applied coating.

22. 将其放到一个已涂过油的碗中，用一块厨巾盖好，让其发酵，直到1个半小时后面发得两倍大为止。

Place in an oiled bowl, cover with a clean kitchen towel and let rise until doubled, about 11/2 hours.

23. 涂层在喷涂过程中所生成的气孔以及热氧化过程中由于热应力而产生的裂纹是造成涂层失效的直接原因。

The pores generated during spraying and the cracks generated during the course of thermal oxidization because of thermal stress are the direct reasons why coatings fail.

24. 传统的溶剂型涂料在喷涂时需大量的快挥发有机溶剂，其在喷涂过程中挥发进入大气，严重地污染了环境。

Traditional solvent based coating needs a lot of quick volatile organic solvent which is volatile into the atmosphere as spraying, so it pollutes environment badly.

25. 介绍了富锌底漆喷涂过程中，基材前处理、涂料混合搅拌等影响因素，并对喷涂技巧及设备作了阐述。

The article made an introduction to substrate pretreatment, coatings mix and agitation during zinc-rich primer spraying. The spray skill and equipment were also introduced.

26. 介绍了富锌底漆喷涂过程中，基材前处理、涂料混合搅拌等影响因素，并对喷涂技巧及设备作了阐述。

The article made an introduction to substrate pretreatment, coatings mix and agitation during zinc-rich primer spraying. The spray skill and equipment were also introduced.