
词语导航
基本信息
词语:轴电流
繁体:軸電流
拼音:zhóu diàn liú
英语翻译
【电】 shaft current
分词翻译
轴的英语翻译:
axes; axis; shaft; spindle
【医】 ax-; ax.; axes; axio-; axis; core
电流的英语翻译:
electric current; electrical current; electricity
【计】 I
【化】 current; electric current; electric current (strength)
【医】 current; electric current; rheo-
翻译例句
1. 电机轴承采用绝缘结构,减小了轴电流对轴承的损伤,提高了轴承寿命。
Insulation structure for bearing, reduce the damage from shaft current and improve the life of bearing.
2. 采取断开轴电流通路的方法,成功解决了这一问题,并提出了进一步的防范措施。
This problem has been successfully solved by adopting method to cut off the path of shaft current, and preventive measures being further put forward.
3. 结合数学模型,讨论了有关矢量控制的原理和直轴电流最小控制的数字实现方法。
And according to the mathematical model, vector control principle and minimal direct axis current control and its digital realized method were discussed.www.WenTIyI.cOm
4. 一种轴电流与轴磁通复合传感器,属检测技术领域,用于解决电机轴电流检测问题。
A composite sensor of shaft current and shaft magnetic flux belongs to checking technical field, and is used to solve the checking problems of shaft current of a motor.
5. 根据交流电动机的工作原理,分析讨论其轴电流产生的原因和表象,提出了防止轴电流产生的方法。
Based on the work principle of AC motor, the article analyzes the cause and phenomenon of alternating-current motor and puts forward the method of removing shaft current.
6. 风吹动叶片旋转,叶片带动连接发电机的轴转动产生电流。
The wind spins the blades, which turn a shaft connected to a generator that produces electricity.
7. 运用磁场的叠加原理及第二类完全椭圆积分,给出了椭圆形稳定电流环垂直轴上的磁感应强度。
According to the superposition principle and the second kind of complete ellipse integral, the magnetic field current circle was calculated.
8. 用该方法对同步控制系统中的自整角机交轴阻尼短路环的损耗和电流进行了间接的实验测试,证实该方法可行。
And the indirect experimental tests of synchro axis damping short-loop loss and current in a synchronous control system were carried out, and proved this method was feasible.
9. YBCO高温超导体有着广阔的应用前景,为改善其弱连接,通常要求强的c轴织构以提高临界电流密度值。
YBCO superconductor has the most promising foreground in the worldwide. To decrease its weak link and improve critical current density, high quality c-axis texture is needed.
10. 介绍力矩式自整角机转子交轴阻尼短路环损耗和电流的一种测试方法。
A test method of torque synchro rotor quadrature axle damping short-loop loss and current was introduced.
11. z轴部件及其控制信号电子束电流产生传导泄漏,CRT是其主要泄漏源。
And the transmission leakage is always generated by the Z-axis components and its current of controlling signal, whose main source is the CRT.
12. 通过对Z轴磁场梯度和匀场线圈电流的多项式拟合,以获得磁场不均匀而引起的相位分布。
The phase mapping method of a field inhomogeneity based on an Z axis pulse field gradient and polynomial fitting procedures of the axial shimming coil currents were described.
13. 本文在交流电机双轴理论的基础上,以异步电动机转子磁通和定子电流为状态的状态方程为模型,推导出一种新型异步电动机磁通观测器。
Based on the two-axis theory of the induction motor and a state equation about the rotor fluxes and stator currents, a new induction motor flux observer is derived.
14. 在轴对称非静态电流分布的情况下,利用麦克斯韦方程组和轴对称性,给出了轴外电磁场的一种计算方法。
Under the circumstances of axial symmetric and non-static current distribution, a method for calculating off-axis electromagnetic field is given by using Maxwells equations and axial symmetry.
15. 调制阴极保护电流而产生的轴频电场最大的幅值比调制腐蚀电流所产生的电场大10倍之多。
The amplitude of electric shaft-frequency electric field by modulating the current of ICCP system is 10 times greater than that of corrosion current.
16. 可以设定电流,自动检测集电环两个电极在一定电流下的电压降,并且还可以检测集电环与轴之间的绝缘电阻及漏电流。
It can be used to set current, automatically detect the voltage drop of the two slip ring electrodes in a certain current, and the insulation resistance and leakage between the slip ring and the axis.
17. 该方法以永磁同步电动机的定子交轴电压或直轴电压为控制量,利用电流的延迟反馈实现了混沌运动的控制。
The direct-axis or quadrature-axis stator voltage is used as manipulated variable and direct-axis or quadrature-axis stator current delay feedback is used for chaos control.
18. 在不同激励电流下,用Hall探极磁场计(ct5)分别测量了沿轴磁场分布。
The field distribution along the axis can be measured by using HALL magnetometer (CT5).
19. 在电流环中引入了一组电流交叉乘积项计算出准确的轴电压控制值,实现控制系统在较宽的速度范围内满足较高的控制精度。
By adopting the new design of circuit loop with cross-multiplying terms, the precision of voltage and speed controlled will be enhanced in a wider speed range.
20. 轧制力矩过大是轧机主传动系统传动轴断裂的主要原因,传统的电机电流过载保护方式不能真实反映轧机主传动系统扭矩的动力学特性。
The breakdown of transmission shaft in the main drive system is due to too high roll torque. Overpower protection mode of motor current does not reflect the true dynamic character of roll torque.
21. 系列的线性轴电机是一款无刷的,直驱动伺服电机,由磁轴和运动线圈组成,运动线圈控制电流量。
S series Linear Shaft Motor is a brushless direct drive tubular linear servomotor consisting of just a magnetic shaft and a moving coil assembly (forcer) which is controlled by the flow of current.
22. 介绍了三相异步电动机的直轴和交轴模型的建立方法,并利用MATLAB语言对两种模型进行仿真,仿真数据包括定子电流、电磁转矩以及转速。
Introduces a constituting method for A-axis and D-axis models of three-phase asynchronous motor. Simulating for those two models by MATLAB language.
23. 基于加工过程数据的膛线测评技术,系统在数据采集中先对C/Z轴电机电流等模拟量数字滤波处理。
The technique of detection-evaluation was based on machining process data. At first, the analog signals such as motor current of C/Z were filtered in data gathering of system.
24. 基于加工过程数据的膛线测评技术,系统在数据采集中先对C/Z轴电机电流等模拟量数字滤波处理。
The technique of detection-evaluation was based on machining process data. At first, the analog signals such as motor current of C/Z were filtered in data gathering of system.
版权声明:问题易所有作品(图文、音视频)均来源网络,版权归原创作者所有,与本站立场无关,如不慎侵犯了你的权益,请联系我们告知,我们将做删除处理!
